Free Ground shipping on every order, contiguous US · No minimum

Water 101 · 6 min read

Reverse osmosis waste water and your septic system

By Mick Preston, Co-founder ·

A couple walks across the green lawn of a rural home in the Utah foothills on a sunny afternoon, the kind of property where RO reject water goes to a septic system
The short answer

An under-sink RO system should not overburden a septic system unless it malfunctions, according to the University of Minnesota's Onsite Sewage Treatment Program. A whole house system is different: it creates "a large wastewater load" that a septic system may not be designed to handle.[1] Reject water usually goes to the house drain, so ask your septic designer or local health department before you buy. Our guide to RO water waste covers the basics.

If your home runs on a septic system, every gallon an RO unit sends to the drain ends up in your tank and drainfield. Here is what the university and EPA sources say, and where you need a local professional instead of an article.

Can you put reverse osmosis on a septic tank?

For a point-of-use system, which treats only your drinking and cooking water, the answer is usually reassuring. The University of Minnesota says a typical unit is 10 to 20 percent efficient, producing 4 to 9 or more gallons of reject water per gallon of treated water, and that it should not overburden a septic system unless it malfunctions.[1]

The "unless it malfunctions" part matters. UNL notes that if the waste flow is too fast, "excessive water flows down the drain."[2] Our drain-keeps-running guide covers that problem. UNL also says that with an RO system, "consideration must be given to the adequacy of the household septic system."[2]

A rough picture, as an illustration only: if your household uses 2 gallons of treated water a day and the system runs at EPA's "typical" five gallons of reject water per gallon, that is about 10 gallons a day to the drain. At the 2.3 limit for WaterSense labeled systems, it is about 4.6.[3] For the ratio math, see RO waste water ratio, explained.

What waste water goes into a septic tank?

Everything that goes down your household drains, and that includes RO reject water. UNL says the wastewater from an RO unit "typically is connected to a household drain" and "increases the load on the septic system."[2]

EPA's septic care page puts the bigger picture in terms of volume. It says household water use runs "as much as 70 gallons per individual, per day," that a single leaky or running toilet "can add as much as 200 gallons of water per day," and that doing all your laundry in one day "could flood your drainfield."[4] It also says efficient water use "improves the operation of a septic system."[4] Against those numbers, a few gallons of reject water from an under-sink unit is small. A running drain line is not.

Can a septic system handle a whole house RO system?

Quite a lot. The University of Minnesota says whole house systems can reach 50 to 75 percent efficiency, but "still create a large wastewater load" that a septic system may not be designed to handle. Reject water from these systems is typically connected to house drains, which adds to the septic load.[1]

The author, Sara Heger, argues that RO use should be a standard question when septic systems are evaluated.[1] So tell your septic designer or service provider before you install anything. They know your tank size, your drainfield or mound, and what your county expects.

An example from UNL shows the scale. A system making 100 gallons a day at a 20 percent recovery rate would "dispose of 80 gallons/day in the waste stream."[2] UNL says most household RO systems are designed for 20 to 30 percent recovery.[2] Treating a whole house is a much bigger job than treating a drinking tap.

What can you do with reverse osmosis wastewater on septic?

The University of Minnesota says reject water "could be used for irrigation or discharged to a separate trench," but only after its volume and contaminant concentration are characterized.[1] That is not a weekend plumbing job. Where wastewater goes is tied to your septic design and local rules, so leave any change to a licensed septic professional and your local health department.

For a general look at your options, see what to do with reverse osmosis waste water and how to reduce it.

If you do look under your sink, check your manual first, turn off the supply valve before you touch any tubing, and stop if a fitting is unfamiliar. An installer or plumber can do it for you. Check for leaks afterward. The free RO waste check walks through a safe flow test.

Frequently asked questions

How to get rid of RO waste water?

Most point-of-use systems send it to the household drain, and the University of Nebraska–Lincoln says that increases the load on the septic system. The University of Minnesota says reject water could be used for irrigation or discharged to a separate trench, but only after its volume and contaminant concentration are characterized. That is a design question for your septic designer or local health department, not a DIY change.

Can I reroute RO waste water away from my septic system myself?

Please don't reroute reject water yourself. Where wastewater goes is tied to your septic design and local rules. Ask a licensed septic professional or your local health department. For a simple check under the sink, read your manual first, shut off the supply valve before touching tubing, stop if a fitting is unfamiliar, and check for leaks afterward. An installer or plumber can do it for you.

What is the best reverse osmosis system for a septic system?

No source we found names one. What the sources do agree on is that less reject water is easier on a septic system. EPA WaterSense labeled point-of-use systems must send 2.3 gallons or less to the drain per gallon of treated water. Whether any system suits your septic system is a question for whoever designed or services it.

What is the most efficient reverse osmosis system for a septic home?

On a septic system, less reject water is the goal. The University of Minnesota notes that some newer systems advertise a 1:1 ratio.[1] EPA WaterSense says labeled systems must send "just 2.3 gallons of water or less down the drain," and that a labeled model saves more than 3,100 gallons a year on average compared with a typical one.[3] Those savings are gallons your tank and drainfield never see.

You can also ask whether your water needs RO at all. The Sentry H2O Wellness System is not an RO system. It sends no reject water to the drain and needs no drain line or electricity. Start with your water report and a conversation with your septic provider, then compare options in how much water reverse osmosis wastes.

Sources

[1] University of Minnesota Water Resources Center, Onsite Sewage Treatment Program, Reverse osmosis (RO) and septic systems, Sara Heger (June 23, 2022). Point-of-use and whole house efficiency, wastewater load, reject water routing.

[2] University of Nebraska–Lincoln Extension, NebGuide G1490, Drinking Water Treatment: Reverse Osmosis (2014). Septic adequacy, drain connection, recovery range, 80 gallons/day example.

[3] U.S. EPA WaterSense, Point-of-Use Reverse Osmosis Systems (last updated August 21, 2026). Typical reject water, 2.3 gallon label limit, 3,100 gallons a year savings.

[4] U.S. EPA, How to Care for Your Septic System (last updated August 17, 2026). Household water use, leaks, laundry timing, efficient water use.

Educational guidance only. This article explains RO reject water and septic systems and cites the University of Minnesota, the University of Nebraska–Lincoln and the U.S. EPA. It makes no claim about any RO brand.

Wally

Water finder

Popular questions

Powered by Bearded Brothers Automation