Water 101 · 7 min read
How to reduce reverse osmosis waste water

You can cut RO waste by keeping the system maintained, making sure it gets steady incoming pressure, and choosing a more efficient model when it is time to replace it. EPA WaterSense says a typical system sends "five gallons or more" to the drain per gallon made, and labeled systems must send 2.3 or less.[1] Read how much water reverse osmosis wastes for the full picture.
If your RO drain bothers you, you are not wrong to look into it. The good news is that some of the waste is within your control. Some of it is built into how the technology works, and it helps to know which is which before you spend money.
Why does the RO system waste so much water?
Only part of the water that enters an RO system comes out as treated water. The University of Nebraska–Lincoln calls this the recovery rate and says "most household RO systems are designed with a 20 percent - 30 percent recovery rate." The rest carries away what the membrane held back and goes to the drain.[2]
EPA WaterSense puts it in gallons: a typical point-of-use system makes "five gallons or more of reject water for every gallon of treated water produced," and some inefficient units make up to 10.[1] We explain how to read those numbers in our waste water ratio guide.
How to minimize RO system waste water
Four things move the number. Three are about your setup, and one is about what happens to the drain water.
Ensure proper water pressure
UNL says "the higher the pressure difference across the membrane the better the rejection of contaminants and recovery rate," and that the incoming line pressure "must be adequate" for the job.[2] Temperature matters too: UNL reports a 1 to 2 percent drop in treated water for every degree below 77°F.[2] You cannot change your well or the weather, but you can find out what pressure your system expects by checking the manual.
UNL adds that "auxiliary pumps can be added to increase incoming water pressure as necessary."[2] If you think low pressure is your problem, ask the maker or a plumber before adding anything.
Perform regular system maintenance
UNL notes that "clogged RO membranes can decrease water flow in the system and cause poor performance," so follow the maker's change schedule for filters and the membrane. It also says "shut-off valves are important to stop water flow when the storage tank is full, so excess water is not wasted," and that "proper adjustment of the flow regulator on the side of the waste stream is important."[2] If your drain never seems to stop, our guide to an RO drain that keeps running walks through it.
Before you touch anything under the sink, check your manual, turn off the supply valve before touching tubing, and stop if a fitting is unfamiliar. An installer or plumber can do this work, and you should check for leaks afterward.
Use a modern system
When it is time to replace the unit, choose a WaterSense labeled model. EPA says labeled systems use "more than 3,100 gallons of water per year" less than a typical system, about 47,000 gallons over its lifetime.[1]
Recycle discharge water
Reuse does not reduce what the system sends out, but it can keep that water from being thrown away. We cover that in what to do with reverse osmosis waste water.
What does a permeate pump do in an RO system?
A permeate pump is an add-on part for tank-style systems. One maker, Watts, describes its non-electric permeate pump as reducing "back pressure from the storage tank" so the system's working pressure stays consistent.[3] In other words, it does not raise the pressure of the water coming in. It helps on the tank side, where a filling tank pushes back against the membrane.
Makers do publish savings figures for their pumps. We could not find an independent test of those figures, so we will not repeat them here. Treat any specific saving as the maker's claim until you see a test report.
Do I need a permeate pump?
Not necessarily. The honest answer depends on your system and your pressure. A pump is one more part to install and eventually replace. If you want one, ask the maker of your system whether it is compatible, since adding parts to a tank-style system is not something to improvise. EPA's page on labeled systems does not mention permeate pumps at all.[1]
Permeate pump vs booster pump
They solve different problems. A booster pump raises the pressure of the water coming in, which is the "auxiliary pump" UNL describes.[2] A permeate pump works on the tank side, as described above.[3] If your feed pressure is low, the first kind is the one aimed at that problem. If your pressure is fine and the tank slows things down, the second is. A water report and your system's manual will tell you more than a forum thread will.
Frequently asked questions
Can I reduce reverse osmosis waste water myself?
Most of the useful steps need no tools: change filters and the membrane on the maker's schedule, check that the tank is not running dry and refilling constantly, and note whether the drain ever runs after the tank is full. Anything under the sink beyond that, such as tubing, a flow restrictor or a pump, is a job for your manual first and an installer or plumber if you are unsure. Turn off the supply valve before you touch tubing, stop if a fitting is unfamiliar, and check for leaks afterward.
What is the most efficient reverse osmosis system?
By the one public yardstick we can cite, a system with the EPA WaterSense label. Labeled systems must send 2.3 gallons or less down the drain for every gallon of treated water they produce, against five gallons or more for a typical system.
How to tell if a permeate pump is bad?
We can't give you a reliable test, because we found no maker's test procedure to quote. Signs worth noticing are a tank that fills much more slowly than it used to, or a drain that keeps running when the tank is full. Both can also come from a clogged membrane or a faulty shut-off valve, so check your manual first and ask the maker or a plumber before replacing parts.
Is there a reverse osmosis filter with reduced water waste?
Yes, in two ways. A WaterSense labeled RO system wastes less than a typical one.[1] Or you can ask whether your water needs a membrane at all. EPA itself notes that filtration, which uses little or no water, may be enough for some needs.[1]
The Sentry H2O Wellness System is not an RO system. It sends no reject water to the drain and needs no drain line or electricity. Take a look at our RO waste check to see what your current system sends down the drain, then compare both options against your own water report.
Sources
[1] U.S. EPA WaterSense, Point-of-Use Reverse Osmosis Systems (last updated August 21, 2026). Typical, inefficient and labeled reject-water figures, yearly savings, filtration note.
[2] University of Nebraska–Lincoln Extension, NebGuide G1490, Drinking Water Treatment: Reverse Osmosis (2014). Recovery range, pressure, temperature, shut-off valve, flow regulator, membrane clogging, auxiliary pumps.
[3] Watts, ERP-1000 Non-Electric Permeate Pump (manufacturer product page, read November 16, 2026). How the pump works, in the maker's words; no savings figure used.
Keep reading
Educational guidance only. This article explains how to reduce RO waste water and cites the U.S. EPA and the University of Nebraska–Lincoln. It makes no claim about any RO brand.
